Chinese translation for "sintered parts"
|
- 烧结零件
Related Translations:
- Example Sentences:
| 1. | Sintered metal materials ; sint - guide - lines ; part 5 : joining of sintered parts
烧结金属材料.烧结指南.第5部分:烧结件的连接 | | 2. | Sintered metal materials ; sint - guide - lines ; part 2 : designing of sintered parts
烧结金属材料.烧结指南.第2部分:烧结件的设计 | | 3. | Sintered metal materials ; sint - guide - lines ; part 1 : machining of sintered parts
烧结金属材料.烧结指南.第1部分:烧结件的机加工 | | 4. | Sintered metal materials ; sint - guide - lines ; part 3 : heat - treatment of sintered parts
烧结金属材料.烧结指南.第3部分:烧结件的热处理 | | 5. | Sintered metal materials ; sint - guide - lines ; part 4 : surface - treatment of sintered parts
烧结金属材料.烧结指南.第4部分:烧结件的表面处理 | | 6. | The analysis results show that , the warping and cracking of sintered part which is induced by thermal stress can be efficiently alleviated by optimizing the geometrical structure of the part to be built , enhancing the pre - heating temperature , and well choosing the building substrate
通过扫描电镜对烧结样品分析发现,烧结件的显微组织为微熔ni颗粒和cusn快速凝固的混合组织,其成形机制为液相烧结。 | | 7. | ( 3 ) there are many flaws in direct laser metal sintering , such as the high remnants stress , micro - hole and micro - crack in sintering parts . in order to solving those problems , the programming of scanning paths is put forward , and several parts are prepared with different scanning paths respectively . the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure , the rigidity of parts prepared by short - side and same direction scanning path is highest , and the density of parts produced with the vertical scanning path is maximal
( 3 )针对采用大功率激光直接烧结镍基高温合金成形金属零件存在的问题,如较大的残余应力,制件中存在着微裂纹、微孔洞等缺陷,初步提出扫描路径的规划,并采用几种不同的扫描方式进行烧结试验,发现采用短边扫描路径和同向扫描能够获得更加细小和分布均匀的组织结构,采用短边同向路径制备的试样其显微硬度最高,而采用变向扫描(垂直)路径制备的试样致密性最好。 | | 8. | Based on the new technology application in new process , this paper makes use of the method of experiment and theory analysis , studies the influence of laser sintering parameter to ps material machining precision , and the rule of the influence of each parameter to sintering part is got through the analysis and study of experiment data and discussion of the formation reason of several disfigurement in sintering part
本文基于新技术在新工艺中的作用，采用试验和理论分析的方法，研究激光烧结参数对聚苯乙烯材料加工精度的影响，通过对试验数据的分析研究，探讨了烧结制件中出现的几种缺陷的形成原因，得出了各参数对烧结制件精度的影响规律。 | | 9. | In this paper , a series of experiments are carried out with dlms for nickel - based metal powder materials , and the effect of process parameters in sample quality was investigated and analyzed . the main works are as following : ( 1 ) the effect mechanism of laser in metal powder and the nucleation mechanism are analyzed . ( 2 ) the process parameters that affect the quality of sintering parts are investigated and the way how they affect is clear
本文基于直接激光金属烧结成形技术,通过对镍基高温合金直接激光烧结成形的研究,从工艺角度研究某型号镍基高温合金的激光直接烧结成形性能以及工艺参数对烧结制件性能的影响,所完成的工作主要有: ( 1 )分析材料与激光相互作用的机理及熔池的动态快速凝固过程。 |
- Similar Words：
- "sintered ore" Chinese translation, "sintered oxide" Chinese translation, "sintered oxide coated cathode" Chinese translation, "sintered oxide-coated cathode" Chinese translation, "sintered part" Chinese translation, "sintered piece" Chinese translation, "sintered piston ring" Chinese translation, "sintered plate" Chinese translation, "sintered platinum" Chinese translation, "sintered polycrystalline diamond" Chinese translation
|
|
|
